Before you commit
Ice maker
repair cost,
band by band.
Bands rather than prices, because the same repair costs differently on a freestanding unit and on a built-in. What does not change is the order — the cheap causes are also the common ones — or the rule that decides repair against replace.
Mon–Sat, 8am–8pm
- 9 priced jobs
- 5 bands
- Price in writing first
Book a visit
Three short steps, about a minute.
or call (844) 773-0701
Loading appointment form…
The appointment form couldn’t load. Please try again.
Your ice maker is priced after it has been tested.
The scale on this page shows where ice maker jobs usually land, not what yours will cost. A bin with no ice could mean a closed valve, a clogged filter, a frozen tube, a bin sensor or a module, and over the phone they all sound the same. So the water is traced and the parts are measured first, the price is set once the failed part is known, and nothing is fitted until you have said yes.
The bands, job by jobWhen you book, ask what the visit costs and whether that amount is credited if the repair goes ahead.
The repair price is given at your home after testing, and work begins only when you agree to it.
When an ice maker is not worth the money, the technician says so, and that answer is part of what the visit is for.
What a repair
usually costs.
Ice maker repairs are mostly small, because the water path is made of small parts: a filter, a line, a valve, a tube, a sensor. On a door or freezer ice maker the larger appliance around it is what a new purchase would cost, so repairing the ice maker nearly always wins. On an undercounter unit the math is still usually in favor of repair unless the sealed cooling system or a discontinued control board has failed. A countertop unit is the one kind where a new machine is often the sensible answer once the motor or the cooling system goes.
| Repair | Relative cost | Notes |
|---|---|---|
| Ice maker module, mold or twisting tray | moderate | A module for a freezer compartment is one of the more affordable parts in this list, while a door compartment module and its wiring sit higher. The price is set only after the water, the temperature and the bin sensor are proved good. |
| Water inlet valve and its fittings | low to moderate | The valve itself is a modest part. Rolling the appliance out, fitting new compression nuts and leak-testing every joint on the way back make up most of the job. |
| Frozen fill tube, tube heater or drip cause | low | Thawing the tube costs only time. The bill rises a step when the heater on a French door model or a dripping valve has to be replaced so the tube stays clear. |
| Auger, auger motor, crusher or chute flap | low to moderate | A flap, a switch or a coupling is small and quick to reach. An auger motor, or the gearbox on a nugget unit, moves the job toward the middle of the scale. |
| Ice bin, compartment cover, gasket or latch | low | Gaskets and latches are inexpensive and fitted from the front. A new bin made for one model, especially one with the auger built in, costs a little more. |
| Water filter, supply line or shutoff valve | lowest | A filter, a braided line or a quarter-turn shutoff is among the least costly work an ice maker can need. A line that has to be run a long way to reach the appliance adds some time. |
| Drain pump, check valve or drain hose | low to moderate | Clearing and rerouting a drain costs little in parts. A new drain pump for an undercounter unit, and pulling the unit from its cabinet to reach it, puts the job in the middle. |
| Cleaning, descaling and sanitizing | low | The work is mostly labor and the maker's cleaner, with no parts in most cases. A unit left uncleaned for years takes longer, and a scaled distribution tube may need replacing. |
| Control board, thermistor or bin sensor | moderate to highest | A thermistor, a bin sensor or a cleaned connector is a small repair. A control board for an undercounter unit is one of the costliest parts an ice maker has, and it can take time to arrive. |
What the diagnostic
visit covers.
The first visit decides what the repair actually is. The fee, and whether it is credited against the repair, is said when you book, before anyone comes out.
The diagnostic visitThe supply valve, the line, the filter and the pressure reaching the appliance, checked before anything is opened.
A forced fill and harvest, so the technician sees whether water arrives, freezes and drops as it should.
The bin sensor, the thermistor, the valve coil and the motor measured with a meter, and the drain and pump checked on a built-in unit.
A named part, the work it takes and its price, or an honest word that the ice maker is not worth repairing.
What moves
the price.
Five things decide where in its band a repair lands. None of them is known for certain until a technician has seen the ice maker.
The typesDoor, freezer, undercounter or countertop
A freezer compartment ice maker is the simplest to reach. A door ice maker adds the dispenser, the auger and a fill tube through the door. An undercounter unit brings its own cooling system and drain, and a countertop unit is small enough that a new one is sometimes the better choice.
Where the water comes from and goes
A supply line that runs a long way, a saddle valve on an old pipe, a well with low pressure or a drain with no floor outlet can add work beyond the ice maker itself. Checking them is part of every visit.
The part that failed
Filters, lines, gaskets and cleaning sit at the low end. Inlet valves, auger motors and drain pumps are a step up, and control boards and the sealed cooling system of a built-in unit sit at the top.
Hard water and how long since the last cleaning
A unit that has been descaled on schedule usually needs only the part that failed. One that has never been cleaned may need a full descaling before the repair can be tested properly.
Which make it is, and how soon its parts come
Parts for everyday makes are often in stock locally. Premium and built-in units can mean costlier parts and longer waits, and a control board no longer made can decide the question by itself. A photo of the model label sent with the booking helps the right part be on hand.
Not every ice maker
breaks the same way.
A door ice maker freezes cubes high in the freezer door and feeds them down the chute to the dispenser, a freezer ice maker fills a tray or a mold and drops the ice into a bin below, an undercounter ice maker is plumbed into the cabinetry with a drain of its own, and a countertop nugget maker pours water from a reservoir you fill by hand. Pick out the one in your home.
All ice maker types
Door ice maker
The ice maker that feeds the dispenser on the outside of a door: tucked into an insulated box in the left door of a French door model, or at the top of the freezer side of a side-by-side, with a chute and an auger carrying cubes to your glass.
Freezer ice maker
The ice maker that sits inside the freezer compartment itself, a tray that twists or a mold with a heater and an ejector, dropping cubes into a bin or drawer you open by hand, with no dispenser on the door.
Undercounter ice maker
A built-in residential ice maker that lives under a kitchen, bar or basement counter, making clear cubes or chewable nugget ice on its own cooling system, with a water line in and a gravity drain or a small drain pump out.
Countertop ice maker
A portable nugget or bullet ice maker that sits on the counter and plugs into an ordinary outlet, fed by a reservoir you fill by hand rather than a water line, with an auger or tray, a small cooling system and a drain plug.
Every kind we serviceAll ice makers, side by side
The archive puts the 4 types against each other: how to tell which you own, what fails on each, and which manufacturers build them.
How to tell yoursWhat fails on eachWho makes them Open the type archive
Questions about
the price.
What does the ice maker diagnostic visit cost?
Why are ice maker repair costs shown as bands and not prices?
Does the diagnosis commit me to the repair?
Could the ice maker repair end up costing more than I approved?
Back to your everyday
Let’s get your ice maker working again.
Three short steps online, or one call. Tell us what you are seeing and pick a window that works.