IceMakerRepair.center (844) 773-0701Mon–Sat, 8am–8pm Book a visit
A technician's hands lift a new white ice maker module into place on the back wall of an open freezer compartment in a US home kitchen, the empty clear bin set aside on the counter.

Ice Maker Assembly Replacement

A new ice maker module fitted in the freezer compartment or the door compartment, after the water, the temperature and the bin sensor have been proved good, so the new part is not blamed for an old problem.

(844) 773-0701

Mon–Sat, 8am–8pm

  • Moderate cost band
  • 5 steps on the visit
  • 4 problems it answers

Book a visit

Three short steps, about a minute.

or call (844) 773-0701

What the ice maker assembly replacement
involves.

The ice maker assembly is the block that holds the mold or the twisting tray, the small motor that empties it, the heater or the tray mechanism, and the switch or light beam that senses a full bin. On most door and freezer designs it is sold and replaced as one piece, because the parts inside are not offered separately. It is also the most commonly replaced part that did not need replacing, so the technician first proves the three things it depends on: water arrives in the right amount, the compartment is cold enough, and the bin sensor reads correctly. Once those check out and the module still will not harvest, the old one comes out on a few screws and one plug, and a new one matched to your model goes in. The fill is adjusted, a cycle is forced, and the first batches are discarded.

How the visit goes

What it usually costsModerate · Ice maker module, mold or twisting tray

A module for a freezer compartment is one of the more affordable parts in this list, while a door compartment module and its wiring sit higher. The price is set only after the water, the temperature and the bin sensor are proved good.

Answers 4 problemsNo Ice Coming From the Ice Maker

Ice Maker Making Too Much Ice · Ice Maker Making Noise · Ice Clumped or Frozen in the Bin

Comes up most onDoor ice maker

Freezer ice maker

Codes that lead hereEO · CI · CI · Defrosting

Bertazzoni French door ice maker showing EO.

Ice maker assembly replacement,
step by step.

Hand back an ice maker that fills, freezes and drops a full batch, with the first cubes thrown out and the bin clean.

01

Confirm water reaches the mold, the compartment temperature is right and the bin sensor reads the bin correctly.

02

Force a harvest to see the module fail with your own eyes rather than assume it.

03

Remove the old module, clean the mounting area and check the wiring plug for corrosion or melted pins.

04

Fit the new assembly matched to your model, set it level and adjust the fill if the design allows.

05

Hand back an ice maker that fills, freezes and drops a full batch, with the first cubes thrown out and the bin clean.

The problems
it answers.

4 of them, from no ice coming from the ice maker to ice clumped or frozen in the bin.

All problems
An open bottom freezer drawer in a US home kitchen showing an empty white ice bin and the gray ice maker mold above it with its row of dry cube cups, a dispensing glass sitting unused on the counter. Most common

No Ice Coming From the Ice Maker

7 causes, cheapest first

Before you call

Tell us this when you book

  1. Whether the ice maker is a twisting tray or a mold with fingers, if you can see it
  2. Whether any ice appears at all, or the mold sits full and frozen
  3. Whether the water dispenser, if you have one, still works
  4. How old the appliance is and whether the ice maker was replaced before

It also answers

Moderate,
on the site's scale.

A module for a freezer compartment is one of the more affordable parts in this list, while a door compartment module and its wiring sit higher. The price is set only after the water, the temperature and the bin sensor are proved good.

Read the full cost guide
RepairRelative cost
Ice maker module, mold or twisting tray moderate
Water inlet valve and its fittings
Frozen fill tube, tube heater or drip cause
Auger, auger motor, crusher or chute flap
Ice bin, compartment cover, gasket or latch
Water filter, supply line or shutoff valve
Drain pump, check valve or drain hose
Cleaning, descaling and sanitizing
Control board, thermistor or bin sensor

Where it
comes up most.

Most bookings: Door ice maker, Freezer ice maker.

All ice maker types

Codes that lead here

All 21 codes that lead here

Often the same visit

A tall stainless French door appliance with a recessed ice dispenser on its left door stands in a bright US home kitchen, a clear glass under the chute catching falling ice cubes.

Door ice maker

 An open bottom freezer drawer in a US home kitchen shows a white ice maker along its back wall above a clear bin heaped with crescent ice cubes.

Freezer ice maker

The makes
we see it on.

27 makes on this site, and the ice maker assembly replacement on any of them. Each mark opens that make's own page.

All 27 brands

Ice maker assembly replacement,
where we come out.

The kitchen, the climate and the building all change how the ice maker assembly replacement goes. These notes are about that, metro by metro.

All service areas

Tampa BayFL · 31 areas

When a Tampa Bay ice maker's module has to be replaced, the new one goes onto a clean water path: the old mold is often crusted from years of mineral-bearing water, so the fill cup, the tube and the valve screen are cleared before the swap is finished.

OrlandoFL · 30 areas

Orlando rental owners want ice again by the next check-in, so a replacement assembly is matched to the model number the manager sends ahead, and the module is fitted and its first harvest watched during the gap between guests.

Miami / South FloridaFL · 47 areas

In a South Florida tower, swapping the ice maker assembly in place is far simpler than moving a built-in column through the building, so the module comes out of the freezer or door where it sits and the unit never leaves its opening.

New York MetroNY · 75 areas

New York's soft water leaves an old ice maker assembly clean inside, so when one is replaced here it is usually for a worn motor, a broken arm or a cracked mold, and a tray-style module in a narrow freezer is often swapped in under an hour.

HoustonTX · 36 areas

Houston's long cooling season keeps ice makers cycling all year, and when a module finally wears out, the new assembly is set up with a fresh filter and a check of the bin's drain holes, since humidity-soaked bins clump around a new unit too.

ChicagoIL · 50 areas

Older Chicagoland freezers often carry a simple tray ice maker with a wire arm, and its replacement assembly is still made for many models, which makes putting in a new module a sensible repair on a unit the family intends to keep.

Los AngelesCA · 95 areas

A Los Angeles ice maker assembly that stopped harvesting is often choked with calcium rather than broken, so the mold and its heater are cleaned and tested first, and the module is replaced only when the motor or the heater has failed outright.

San DiegoCA · 31 areas

When a San Diego ice maker module is replaced, the technician also descales the water path feeding it, since the region's imported hard water would scale a new mold within months and make the new assembly look defective.

San Francisco Bay AreaCA · 74 areas

Bay Area remodels leave many door and drawer ice makers inside panel-front columns, and replacing the assembly there means working inside the freezer without disturbing the custom panel, so the part and the approach are settled from the model plate ahead of time.

A parent and a child filling two glasses with ice from the door dispenser in a bright family kitchen
For the heart of your home.

Questions about
the ice maker assembly replacement.

Can I just buy an ice maker module online and swap it myself?
On some freezer models the swap is simple, but the module is often not the part that failed. If the valve, the fill tube or the bin sensor is the real problem, a new module will not make ice either, and many parts sellers do not take electrical parts back once they are installed.
The mold is full of frozen water but nothing comes out. Is the module dead?
Very often, yes: water arrived and froze, which means the supply and the temperature are fine, and the part that should empty the mold did not. Before it is condemned, the technician checks that the bin sensor is not holding it off and that the harvest is not simply waiting on a timer.
Why do the first few batches after a new ice maker look odd?
The new mold or tray and the fill tube still hold air and a little manufacturing residue, and the water in the line has been sitting. Throw out the first two or three batches; by the end of the first day the cubes should be full-sized and clear of any taste.
Can a door ice maker be swapped for a freezer one, or the other way round?
No. Each design fits the compartment, the wiring and the airflow of its own model. The replacement has to be the module listed for your model number, which is why a photo of the label helps before the visit.

Back to your everyday

Ready to book the ice maker assembly replacement?

Have these to hand: whether the ice maker is a twisting tray or a mold with fingers, if you can see it, whether any ice appears at all, or the mold sits full and frozen, whether the water dispenser, if you have one, still works, how old the appliance is and whether the ice maker was replaced before.

Schedule a repair Call (844) 773-0701
(844) 773-0701 Schedule a repair