GE Profile Opal 2.0 filter light pulsing
On Opal 2.0 models that take the Opal water filter, a pulsing filter light means the filter has expired or is waiting for its first setup.
Mon–Sat, 8am–8pm
- Mode, not a failure
- No repair needed
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 773-0701
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Filter light pulsing
actually means.
On Opal 2.0 models that take the Opal water filter, a pulsing filter light means the filter has expired or is waiting for its first setup. Holding the filter button starts or resets the filter tracker.
GE Profile ice maker display
What to do when Filter light pulsing shows on the ice makerKind of codeMode, not a failure
Something the ice maker was switched into, often without anyone noticing, rather than something that broke: ice turned off from the panel or by the wire arm lifted while reaching into the bin, a control lock, a Sabbath setting, a cleaning cycle still running, a reminder that the water filter is due. No part has worn out, and the ice maker's own buttons or arm put it right.
Usually leads toNo repair
If a filter is installed and new, hold the filter button to start the tracker.
Shows up asIce Tastes or Smells Bad
The ice tastes bad or smells stale, musty, of plastic or of whatever else is in the freezer, even though a glass of tap water tastes fine.
MakeGE Profile
GE Profile ice maker repair, including the countertop nugget ice makers that run from a reservoir instead of a water line.
SourceGE Profile Opal 2.0 owner's manual 49-9000075
GE Profile Opal 2.0 models with the optional filter.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Filter light pulsing on its ice makers. Follow it to the end: the last card says whether this is a visit.
If a filter is installed and new, hold the filter button to start the tracker.
If the filter is old, fit a new Opal filter until it clicks in place, then hold the filter button.
Tap the filter button if you only want to hide the status light.
If the light keeps pulsing after a reset, book a visit.
Cleared?
The ice maker is filling and dropping cubes again and no part was needed. If the same code returns during the next harvest, or water shows up on the floor again, book it as a new problem.
What not to do
The pulsing light does not stop ice production by itself. It is a tracker, and it does not test the water that passes through the filter.
What you may
notice with it.
The ice maker problems Filter light pulsing tends to arrive with. Answer these at the ice maker before anyone is booked.
All problems
Ice Tastes or Smells Bad
5 causes, cheapest first
No repair indicated
Nothing to repair.
Something the ice maker was switched into, often without anyone noticing, rather than something that broke: ice turned off from the panel or by the wire arm lifted while reaching into the bin, a control lock, a Sabbath setting, a cleaning cycle still running, a reminder that the water filter is due. No part has worn out, and the ice maker's own buttons or arm put it right.
GE Profile
ice makers.
GE Profile ice maker repair, including the countertop nugget ice makers that run from a reservoir instead of a water line.
GE Profile ice maker repairMore GE Profile codes
Mode, not a failure on other makes
Door ice maker
The ice maker that feeds the dispenser on the outside of a door: tucked into an insulated box in the left door of a French door model, or at the top of the freezer side of a side-by-side, with a chute and an auger carrying cubes to your glass.
Freezer ice maker
The ice maker that sits inside the freezer compartment itself, a tray that twists or a mold with a heater and an ejector, dropping cubes into a bin or drawer you open by hand, with no dispenser on the door.
Undercounter ice maker
A built-in residential ice maker that lives under a kitchen, bar or basement counter, making clear cubes or chewable nugget ice on its own cooling system, with a water line in and a gravity drain or a small drain pump out.
In GE Profile's own words
If the filter light is pulsing, it means your filter is expired or awaiting initial setup.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile Opal 2.0 models with the optional filter.
GE Profile Filter light pulsing ice maker repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Filter light pulsing.
Can I clear Filter light pulsing myself?
Why does the filter light pulse on a brand-new Opal 2.0?
Which filter fits the Opal 2.0?
Does the Opal 2.0 stop making nugget ice when the filter light pulses?
Back to your everyday
Still showing Filter light pulsing?
Book with the code or the blink pattern written exactly as the ice maker shows it, the full model number, and whether there is any water on the floor — when there is a code, that is where the diagnosis starts.