GE Profile Opal Defrosting indicator
If the Opal 2.0 detects a frozen auger and low ice production, it lights Defrosting and runs a rinse to thaw itself, then goes back to making ice.
Mon–Sat, 8am–8pm
- Ice making and harvest
- Ice maker assembly replacement
- Source: GE Profile
Book a visit
Three short steps, about a minute.
or call (844) 773-0701
Loading appointment form…
The appointment form couldn’t load. Please try again.
What Defrosting
actually means.
If the Opal 2.0 detects a frozen auger and low ice production, it lights Defrosting and runs a rinse to thaw itself, then goes back to making ice. GE says the automatic defrost can take 30 to 45 minutes, and the front button will not respond during it.
GE Profile ice maker display
What to do when Defrosting shows on the ice makerKind of codeIce making and harvest
The ice maker froze a batch and could not release it, or the harvest never started: the ejector arm or the twisting tray stalled, the mold heater did not loosen the cubes, or the arm that senses a full bin reported the wrong thing. Ice jammed against the arm and a bin pushed in crooked are cleared first; a motor module or a whole ice maker assembly comes after.
Usually leads toIce maker assembly replacement
A new ice maker module fitted in the freezer compartment or the door compartment, after the water, the temperature and the bin sensor have been proved good, so the new part is not blamed for an old problem.
Shows up asNugget Ice Maker Not Making Nugget Ice
A nugget ice maker not making ice runs and hums but drops nothing, makes wet slush instead of crisp pellets, or stops after a few batches with a light on.
MakeGE Profile
GE Profile ice maker repair, including the countertop nugget ice makers that run from a reservoir instead of a water line.
SourceGE Profile Opal 2.0 owner's manual 49-9000075
GE Profile Opal 2.0 nugget ice makers.
Before you book,
in this order.
Each step comes from GE Profile's own guidance for Defrosting on its ice makers. Follow it to the end: the last card says whether this is a visit.
Let the defrost finish; do not unplug the unit partway through.
Keep the Opal at least 4 inches from walls on the sides and back so it can shed heat.
If Defrosting comes on often or the unit squeaks, descale it with white vinegar as the manual describes.
If it keeps defrosting and still makes little ice, book a visit.
Still there?
It usually turns into ice maker assembly replacement. Book with the code and the model number.
What not to do
Defrosting is not an error in the usual sense; it is the Opal clearing ice from its own auger. Frequent defrosts, though, usually mean mineral scale is building up inside.
What you may
notice with it.
The ice maker problems Defrosting tends to arrive with. Answer these at the ice maker before anyone is booked.
All problems
Where Defrosting usually leads
Ice maker assembly replacement.
GE Profile
ice makers.
GE Profile ice maker repair, including the countertop nugget ice makers that run from a reservoir instead of a water line.
GE Profile ice maker repairMore GE Profile codes
Ice making and harvest on other makes
All 20 codes of this kind
Door ice maker
The ice maker that feeds the dispenser on the outside of a door: tucked into an insulated box in the left door of a French door model, or at the top of the freezer side of a side-by-side, with a chute and an auger carrying cubes to your glass.
Freezer ice maker
The ice maker that sits inside the freezer compartment itself, a tray that twists or a mold with a heater and an ejector, dropping cubes into a bin or drawer you open by hand, with no dispenser on the door.
Undercounter ice maker
A built-in residential ice maker that lives under a kitchen, bar or basement counter, making clear cubes or chewable nugget ice on its own cooling system, with a water line in and a gravity drain or a small drain pump out.
In GE Profile's own words
If the ice maker has detected a frozen auger and low ice production then the Defrosting indicator will light up.
Every code on this site is taken from the manufacturer's documentation, never from a forum or a parts listing. GE Profile Opal 2.0 nugget ice makers.
GE Profile Defrosting ice maker repair,
where we come out.
The same visit in every metro below: the code, the model number, and a diagnosis before any part is ordered.
All service areasTampa BayFL · 31 areas
Miami / South FloridaFL · 47 areas
New York MetroNY · 75 areas
HoustonTX · 36 areas
ChicagoIL · 50 areas
Los AngelesCA · 95 areas
San DiegoCA · 31 areas
Questions
about Defrosting.
Can I clear Defrosting myself?
How long does an Opal stay on Defrosting?
Why does my Opal squeak before it shows Defrosting?
Is Defrosting on an Opal a reason to book a visit?
Back to your everyday
Still showing Defrosting?
Book with the code or the blink pattern written exactly as the ice maker shows it, the full model number, and whether there is any water on the floor — when there is a code, that is where the diagnosis starts.